It's not heating — clothes come out cold and damp — heating element, high-limit thermostat, thermal fuse
It's not drying — it takes two or three cycles to get clothes dry — blower wheel, thermistor, moisture sensor
The drum isn't turning — I hear it hum but nothing spins — drive belt, idler pulley
It's making a squealing, thumping, or scraping noise — drum roller, idler pulley, drum
It won't start — nothing happens when I press the button — door switch, door latch, control board
There's a burning smell when it runs — drive belt, heating element, drum roller
It shuts off before the clothes are actually dry — high-limit thermostat, thermistor, moisture sensor
The door won't stay shut or sags open — door hinge
Codes on the display
Code
What it means
Evidence
D80
—
a repair video for this brand and appliance, not confirmed on this model
D90
—
a repair video for this brand and appliance, not confirmed on this model
D95
—
a repair video for this brand and appliance, not confirmed on this model
E5
—
a repair video for this brand and appliance, not confirmed on this model
TE1
—
a repair video for this brand and appliance, not confirmed on this model
DE
—
a repair video for this brand and appliance, not confirmed on this model
EE
—
a repair video for this brand and appliance, not confirmed on this model
Documented failures
Heating element
Usually DIYVendor replaces this part if the dryer is not warming the air
DIY once tested. If the high-limit thermostat also failed with it, replace both — a tripped thermostat is often collateral damage from the same overheat event.
Try this first — it costs nothing. Clean the lint screen and check the vent duct isn't blocked — the most common 'no heat' complaint on a good element is airflow choking the heat off.
Check, in this order
Confirm this is actually an electric dryer before ordering anything — gas models don't have this part.
Clean the lint screen and clear the vent duct first; restricted airflow makes a good element trip its safety thermostat and look dead.
Test the element coil for continuity with a multimeter before replacing it — an open circuit confirms the fault.
Before you open anything
Unplug the dryer or cut power at the breaker — the element carries full line voltage.
Let the element housing cool before touching it; it stays hot after use.
This part exists on electric dryers only — a gas dryer heats with a burner and igniter/gas-valve coil instead, which this component set doesn't cover.
Tools
#2 Phillips screwdriver ($6) — Panel and bracket screws.
5/16" nut driver ($8) — Cabinet and bracket screws on most front-load machines are 5/16" hex.
Multimeter ($25) — Confirm continuity before replacing an electrical part.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Access the element housing, usually behind the rear panel or under the drum depending on model.
Photograph the wiring before disconnecting anything.
Release the housing, swap the element coil, and reseat every wire on its original terminal.
Restore power and run a short heat cycle before closing the cabinet back up.
How you know it worked. The dryer produces steady heat through a full cycle and clothes come out hot to the touch at the end.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $43.79–$45.95 against $864.51 for a new machine (5.3%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Thermal fuse
Usually DIYVendor replaces this part if the dryer will not dry properly
DIY. If the fuse has tripped more than once, treat the vent as the real problem, not the fuse.
Try this first — it costs nothing. Clear the vent duct fully before replacing the fuse — otherwise the new one trips again on the next load.
Check, in this order
Clear the vent duct first — a blocked vent is the usual reason a thermal fuse trips in the first place, and a fresh fuse will trip again if the airflow problem isn't fixed.
Test the fuse for continuity; it's a one-time safety part and doesn't reset.
Check the high-limit thermostat too — the same overheat event often takes both out.
Before you open anything
Unplug the dryer or cut power at the breaker.
If this is a gas dryer, also shut off the gas supply valve before opening the cabinet.
Tools
Multimeter ($25) — Confirm continuity before replacing an electrical part.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Access the fuse, usually on the blower housing or exhaust duct near the back.
Photograph the wiring, then disconnect the two spade terminals.
Snap in the replacement and reconnect both terminals firmly.
How you know it worked. The dryer powers on and completes a full heated cycle without cutting out.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $8.89 against $864.51 for a new machine (1.0%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Drive belt
Usually DIYVendor replaces this part if the drum will not spin
DIY once you have a photo of the old routing. If there's no routing diagram anywhere on the cabinet and you didn't photograph it beforehand, get help rather than guess.
Try this first — it costs nothing. Nothing free — a broken belt needs replacing, but check the idler pulley and rollers at the same time so it doesn't fail again in a month.
Check, in this order
Spin the drum by hand with the machine unplugged — a snapped belt lets it spin freely with no resistance.
Look for a burnt-rubber smell or belt dust inside the cabinet, which confirms slipping before failure.
Check the idler pulley and drum rollers while the belt is off; a worn one is usually why the belt failed.
Before you open anything
Unplug the dryer or cut power at the breaker.
If this is a gas dryer, also shut off the gas supply valve before opening the cabinet.
Tools
5/16" nut driver ($8) — Cabinet and bracket screws on most front-load machines are 5/16" hex.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Remove the top and front panels to access the drum.
Photograph the belt routing around the drum and motor before removing the old one.
Fit the new belt in the exact same path and re-tension it around the idler pulley.
Reassemble and spin the drum by hand to confirm it tracks straight before running a cycle.
How you know it worked. The drum turns smoothly and quietly through a full cycle with no slipping sound.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $11.97–$28.99 against $864.51 for a new machine (3.4%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Moisture sensor
Usually DIYVendor replaces this part if it is damaged or missing
DIY.
Try this first — it costs nothing. Scrub the sensor bars with a fine abrasive pad or rubbing alcohol — coated bars are the number one cause of a bad auto-dry read.
Check, in this order
Clean the two metal sensor bars inside the drum opening — fabric softener sheets coat them and cause exactly this symptom for free.
Confirm you're not running Timed Dry by mistake, which bypasses the sensor entirely.
Check the wiring harness to the sensor bars for a loose connector.
Before you open anything
Unplug the dryer or cut power at the breaker.
Tools
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Flashlight ($0) — Boot, sump and pump housings are dark.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Open the door and locate the sensor bars just inside the drum opening.
If cleaning doesn't fix it, trace the wiring back to its connector.
Photograph the connector, release it, and swap the sensor assembly.
How you know it worked. Auto-dry consistently matches the actual dryness of the load across several runs.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $9.81–$30.71 against $864.51 for a new machine (3.6%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Thermistor
Usually DIYVendor replaces this part if the dryer is not drying properly
DIY.
Try this first — it costs nothing. Wipe down the sensor area near the lint screen housing — a film of fabric softener residue throws off the reading for free.
Check, in this order
Clean the lint screen and vent — a coated sensor from lint buildup reads temperature wrong the same way a failed one does.
Test resistance against the manufacturer's expected range for the sensor at room temperature.
Confirm the moisture sensor bars aren't also coated, since both live in the same area.
Before you open anything
Unplug the dryer or cut power at the breaker.
Tools
Multimeter ($25) — Confirm continuity before replacing an electrical part.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Locate the thermistor, usually clipped near the blower housing or lint screen duct.
Photograph the connector, unclip the sensor, and swap it.
Reseat the connector fully — a loose connection reads the same as a dead sensor.
How you know it worked. Cycle times and heat levels behave consistently load to load instead of drifting.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $8.97–$10.99 against $864.51 for a new machine (1.3%).Part cost only. A service call adds a regional diagnostic fee plus labour.
High-limit thermostat
Usually DIYVendor replaces this part if the dryer will not dry properly
DIY once tested. If it keeps tripping after the vent is clear, that points at the element instead.
Try this first — it costs nothing. Clear the vent duct — a choked vent overheats the airflow and trips this part long before the load is dry.
Check, in this order
Clear the vent duct first — restricted airflow is the single most common reason this part trips early.
Test for continuity; a thermostat that won't close even when cool has failed.
Check the heating element and thermal fuse in the same circuit while the housing is open.
Before you open anything
Unplug the dryer or cut power at the breaker.
If this is a gas dryer, also shut off the gas supply valve before opening the cabinet.
Tools
Multimeter ($25) — Confirm continuity before replacing an electrical part.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
5/16" nut driver ($8) — Cabinet and bracket screws on most front-load machines are 5/16" hex.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Access the thermostat, mounted on the heating element housing or blower duct depending on model.
Photograph the terminals before removing them.
Swap the thermostat and reconnect every terminal in its original position.
How you know it worked. A full cycle completes at normal heat without an early cutoff.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $7.84–$43.05 against $864.51 for a new machine (5.0%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Control board
Usually DIYVendor replaces this part if the dryer will not power on
Get a technician to confirm before buying a board — it's the most expensive part on the machine and the most commonly misdiagnosed.
Try this first — it costs nothing. Power-cycle at the breaker and check the outlet with a different device — a nuisance trip or a dead outlet looks identical to a dead board.
Check, in this order
Rule out the outlet, the door switch, and the thermal fuse first — all three present as a dead dryer and are far cheaper.
Inspect the board for scorching, a burnt smell, or a swollen capacitor.
Power-cycle at the breaker for a full minute before condemning the board.
Before you open anything
Unplug the dryer or cut power at the breaker.
Photograph every connector before removing any — boards have many identical-looking plugs.
Tools
T20 Torx driver ($7) — Some control and door assemblies use Torx rather than hex.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Multimeter ($25) — Confirm continuity before replacing an electrical part.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Access the board, typically behind the control console or a rear panel.
Transfer connectors one at a time against your photographs.
Seat the new board fully and confirm no pins are bent before closing it up.
How you know it worked. The dryer powers up normally and completes a full cycle without faults.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Weigh it - this part is a meaningful share of a new machine. Part $303.82 against $864.51 for a new machine (35.1%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Drum roller
Usually DIYVendor replaces this part if the drum does not spin properly or is noisy
DIY. Get help supporting the drum if you're working solo — it's awkward to hold and service at the same time.
Try this first — it costs nothing. Nothing free — a worn roller is a mechanical wear item, not a cleaning fix.
Check, in this order
Spin the drum by hand and feel for a flat spot or grinding resistance — worn rollers thump in rhythm with drum speed.
Look at the roller wheel itself for a flat side or cracked bearing.
Replace rollers in pairs at the back of the drum — if one is worn the other is close behind.
Before you open anything
Unplug the dryer or cut power at the breaker.
If this is a gas dryer, also shut off the gas supply valve before opening the cabinet.
Tools
5/16" nut driver ($8) — Cabinet and bracket screws on most front-load machines are 5/16" hex.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Spring/hose-clamp pliers ($15) — The boot's outer spring clamp is very hard to seat without them.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Remove the front or rear panel to expose the roller shafts, depending on model.
Photograph the position before removing the drum from its track.
Release the retaining ring or clip, swap the roller, and reseat the drum on its track.
How you know it worked. The drum turns without a rhythmic thump and the noise is gone through a full cycle.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $15.99 against $864.51 for a new machine (1.8%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Drum
Usually DIYVendor replaces this part if it is damaged or missing
Get a second person to help lift and seat the drum — it's not dangerous, just heavy and easy to drop.
Try this first — it costs nothing. Nothing free — a cracked baffle or worn drum surface needs replacing, but check the cheaper wear parts around it first.
Check, in this order
Rule out the rollers, felt seal, and glides individually before assuming the drum itself is at fault — those wear first and are far cheaper.
Look inside the drum for a cracked baffle or lifter fin, which causes thumping specifically when clothes tumble past it.
Check the drum surface for scoring from a failed roller that's been ignored too long.
Before you open anything
Unplug the dryer or cut power at the breaker.
If this is a gas dryer, also shut off the gas supply valve before opening the cabinet.
The drum is heavy and awkward alone — get help lifting it out.
Tools
5/16" nut driver ($8) — Cabinet and bracket screws on most front-load machines are 5/16" hex.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Spring/hose-clamp pliers ($15) — The boot's outer spring clamp is very hard to seat without them.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Remove the front and top panels and the belt to free the drum.
Photograph the belt routing and support positions before lifting the drum out.
Fit the replacement drum or baffle and re-thread the belt exactly as photographed.
Spin the drum by hand to confirm it seats and tracks evenly before running a cycle.
How you know it worked. The drum turns smoothly and quietly with no thumping or grinding through a full cycle.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $22.00–$22.12 against $864.51 for a new machine (2.6%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Blower wheel
Usually DIYVendor replaces this part if the dryer is noisy or if no air is flowing
DIY. If the wheel is fine but airflow is still weak after clearing everything, the vent run itself may be too long or have too many bends — that's a duct problem, not a parts problem.
Try this first — it costs nothing. Clean the lint screen and clear the full vent duct run to the outside — weak airflow is caused by a blocked vent far more often than a broken blower wheel.
Check, in this order
Clear the vent duct and lint screen first — a clogged vent starves airflow the same way a cracked or clogged blower wheel does, and costs nothing to rule out.
Look and listen for a rattle near the back of the cabinet, which points at a cracked or loose wheel rather than a vent blockage.
Check the wheel for lint packed solid around the blades once the housing is open.
Before you open anything
Unplug the dryer or cut power at the breaker.
If this is a gas dryer, also shut off the gas supply valve before opening the cabinet.
Tools
5/16" nut driver ($8) — Cabinet and bracket screws on most front-load machines are 5/16" hex.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Vacuum with a brush head ($0) — Condenser coils clog with dust and cause the same warm-fridge symptom as a dead fan.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Remove the rear or front panel to reach the blower housing, depending on model.
Photograph the housing and motor shaft connection.
Clear packed lint from the wheel and housing, or swap the wheel if it's cracked, and reseat it fully on the motor shaft.
How you know it worked. Loads dry in one normal cycle and the exhaust airflow outside is strong when you hold your hand near the vent hood.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $19.39–$63.65 against $864.51 for a new machine (7.4%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Door switch
Usually DIYVendor replaces this part if the dryer will not run
DIY.
Try this first — it costs nothing. Check that nothing is obstructing the door from closing fully, and that the strike isn't bent — a door that looks shut but isn't quite there won't trigger the switch.
Check, in this order
Confirm the door latches firmly and the strike lines up with the switch — a misaligned door won't trigger a good switch.
Test the switch for continuity in the closed position; the dryer won't start on a failed switch even though the door feels shut.
Check for a bent or broken strike on the door itself before condemning the switch.
Before you open anything
Unplug the dryer or cut power at the breaker.
Tools
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Multimeter ($25) — Confirm continuity before replacing an electrical part.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Open the door panel or console to reach the switch, model dependent.
Photograph the wiring, then swap the switch.
Confirm alignment with the door strike before closing everything back up.
How you know it worked. The dryer starts reliably on a normal door close, every time.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $8.68–$18.95 against $864.51 for a new machine (2.2%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Idler pulley
Usually DIYVendor replaces this part if the motor is running but the drum will not spin
DIY.
Try this first — it costs nothing. Nothing free — a squealing pulley bearing is a wear item.
Check, in this order
Listen for a squeal that rises and falls with drum speed — that's the pulley bearing, not the belt itself.
Spin the pulley wheel by hand once exposed; roughness or grinding confirms the bearing has failed.
Check belt tension at the same time; a worn pulley often lets the belt run loose.
Before you open anything
Unplug the dryer or cut power at the breaker.
If this is a gas dryer, also shut off the gas supply valve before opening the cabinet.
Tools
5/16" nut driver ($8) — Cabinet and bracket screws on most front-load machines are 5/16" hex.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Remove the panel needed to reach the belt and pulley assembly.
Photograph the belt routing around the pulley before releasing tension.
Swap the pulley and re-tension the belt exactly as it was routed.
How you know it worked. The squeal is gone and the belt runs quietly at full drum speed.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $6.47 against $864.51 for a new machine (0.7%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Door latch
Usually DIYVendor replaces this part if it is damaged or missing
DIY.
Try this first — it costs nothing. Wipe down the latch and strike — built-up lint and fabric softener residue can make a good latch feel loose.
Check, in this order
Check for a cracked or worn latch hook, which lets the door feel shut without fully engaging.
Confirm the strike plate on the door frame is aligned.
Test that the door switch itself is fine before assuming the latch is the problem.
Before you open anything
Unplug the dryer or cut power at the breaker.
Tools
#2 Phillips screwdriver ($6) — Panel and bracket screws.
T20 Torx driver ($7) — Some control and door assemblies use Torx rather than hex.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Access the latch assembly from the front panel or console.
Photograph the mounting screws and switch wiring.
Swap the latch and check that the door catches firmly before reassembling.
How you know it worked. The door catches solidly and the dryer starts on a normal close.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $33.95–$46.40 against $864.51 for a new machine (5.4%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Door hinge
Usually DIYVendor replaces this part if it is damaged or missing
DIY, but easier with two people holding the door.
Try this first — it costs nothing. Tighten the hinge mounting screws first — a sagging door is often just loose screws, not a broken hinge.
Check, in this order
Open the door and check whether it sags immediately or only after a while — immediate sag points at a stripped hinge mount.
Look for cracked plastic at the hinge pin or a stretched hinge spring.
Check that both hinge screws are actually tight before replacing anything.
Before you open anything
Unplug the dryer or cut power at the breaker.
Support the door when you release the hinge screws — it's heavier than it looks and will drop.
Tools
5/16" nut driver ($8) — Cabinet and bracket screws on most front-load machines are 5/16" hex.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Support the door and remove the hinge-side mounting screws.
Photograph the position, then swap the hinge bracket.
Reinstall and check the door holds level at a half-open position before closing it fully.
How you know it worked. The door holds its position when opened and closes without dropping or binding.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $93.44 against $864.51 for a new machine (10.8%).Part cost only. A service call adds a regional diagnostic fee plus labour.
If you replace it instead
Configuration-matched to this machine (vented, 240.0, ~7.4 cu ft). Prices are UPC-verified Amazon listings, not estimates. Like-for-like replacement rarely pays for itself on energy alone — replace for fit and features, or because the repair maths above says so.
Model
Capacity
Energy cost
Price
Price checked
Kenmore 7165*20* Digits marked * vary by colour/finish; any model in this series matches.
A candidate must match this machine's configuration (style, fuel and defrost class) before price or efficiency is considered. Prices are a snapshot from the date shown; availability is not monitored — check the retailer before buying.
Or see the whole class
We rank every dryer we hold certification data for, within its own size and configuration class, so you are comparing machines that would fit the same space. See the dryer rankings →