Maytag MFI2570FEZ00

Start relay

The start relay itself is a genuinely owner-replaceable part - it clips on and off the outside of the compressor. The compressor and its sealed refrigerant system are different: never open refrigerant lines or attempt to recharge the system yourself - that requires EPA Section 608 certification. If a new relay doesn't bring the compressor to life, the compressor itself or the sealed system is the next suspect, and that's a certified technician's job.

Check, in this order

1. Listen for a repeated clicking sound near the compressor every few minutes - that's the classic start-relay symptom, the compressor trying and failing to start.
2. Confirm the fridge is actually receiving power (outlet, cord, breaker) before suspecting the relay.
3. Pull the relay off the compressor terminals and shake it gently - a rattle can indicate a failed relay, though this isn't conclusive on its own.

Before you open anything

• Unplug the refrigerator.
• Confirm the outlet is dead with a non-contact voltage tester before touching anything near the compressor.
• The relay clips onto the compressor terminals - handle it, not the compressor's refrigerant lines or fittings.

Tools

• #2 Phillips screwdriver ($6) — Panel and bracket screws.
• Multimeter ($25) — Confirm continuity before replacing an electrical part.
• Phone camera ($0) — Photograph connector positions before unplugging anything.
• Non-contact voltage tester ($18) — Many ranges are hard-wired, not plugged in - confirm the circuit is actually dead before touching it.

The repair, in order

1. Unclip the compressor terminal cover and locate the relay/overload assembly clipped to the compressor's side terminals.
2. Photograph the wiring before removing anything.
3. Pull the relay off the terminals and test it with the multimeter's continuity function between its terminals.
4. Fit the replacement relay onto the compressor terminals in the same orientation, and refit the terminal cover.

How you know it worked. The compressor starts and runs without clicking, and the fridge pulls down to temperature over the following hours.

In your manual: the manual — checked; its troubleshooting section does not cover this part.

Component demonstration
Whirlpool Matrix Refrigerator Start Relay Replacement W11092533RepairClinic.com · not filmed on this specific model; the procedure is for the component

Worth fixing? Repair - the part is a small fraction of a new machine. Part $51.99–$54.00 against $1,399.99 for a new machine (3.9%).Part cost only. A service call adds a regional diagnostic fee plus labour.

Ice maker

DIY. Call someone if the fill valve or water line inside the cabinet is involved.

Check, in this order

1. Give it the manual's 12 hours after any install or reset before judging it.
2. Confirm the freezer is below 0 F - the manual lists a warm freezer as a cause of no ice.
3. Check the dispenser lock is off, the ice maker is switched on, and the water line stop cock is open.
4. Hollow or small cubes point at the water filter or supply rather than the ice maker.

Before you open anything

• Unplug the refrigerator.
• Turn off the water supply before disturbing the fill line.

Tools

• #2 Phillips screwdriver ($6) — Panel and bracket screws.
• Flashlight ($0) — Boot, sump and pump housings are dark.
• Phone camera ($0) — Photograph connector positions before unplugging anything.
• Shallow pan and towels ($0) — Residual water always comes out, even after draining.

The repair, in order

1. Give it the manual's 12 hours after any install or reset before calling it faulty.
2. Confirm the freezer is below 0 F - the manual lists a warm freezer as a cause of no ice.
3. Check the water line and stop cock, and that the dispenser lock is off.
4. If ice is hollow or small, replace the water filter before the ice maker.
5. Photograph the harness, unclip the assembly, fit the replacement.

How you know it worked. A full harvest within 24 hours, cubes solid rather than hollow.

In your manual: The ice maker is not producing ice or not enough ice — page 14

Component demonstration
Whirlpool Refrigerator Replace Ice Maker Auger Motor W10309868RepairClinic.com · not filmed on this specific model; the procedure is for the component

Worth fixing? Repair - the part is a small fraction of a new machine. Part $62.70–$89.95 against $1,399.99 for a new machine (6.4%).Part cost only. A service call adds a regional diagnostic fee plus labour.

Dispenser

DIY.

Check, in this order

1. Check the dispenser lock is off.
2. Look for ice jamming the chute - the manual notes jams after about three weeks unused.
3. Confirm the water filter is not overdue.

Before you open anything

• Unplug the refrigerator.
• Turn off the water supply.

Tools

• #2 Phillips screwdriver ($6) — Panel and bracket screws.
• Flashlight ($0) — Boot, sump and pump housings are dark.
• Phone camera ($0) — Photograph connector positions before unplugging anything.
• Shallow pan and towels ($0) — Residual water always comes out, even after draining.

The repair, in order

1. Check the dispenser lock is off and the filter is not overdue.
2. Look for ice jamming the chute - the manual notes ice jams after about three weeks unused.
3. Photograph the harness before removing the dispenser assembly.

How you know it worked. Both water and ice dispense normally.

In your manual: The water and ice dispenser will not operate properly — page 15

Component demonstration
Whirlpool Refrigerator Ice Dispenser Solenoid #W10309866RepairClinic.com · not filmed on this specific model; the procedure is for the component

Worth fixing? Repair - the part is a small fraction of a new machine. Part $94.00–$130.31 against $1,399.99 for a new machine (9.3%).Part cost only. A service call adds a regional diagnostic fee plus labour.

Control board

Get a technician to confirm before buying a board. It is the most expensive part here and the most commonly misdiagnosed.

Check, in this order

1. Rule out fans, sensor, damper and door switch first - the board is the expensive part they all get blamed for.
2. Inspect the board for scorching or swollen capacitors.

Before you open anything

• Unplug the refrigerator.
• Photograph every connector before removing any.

Tools

• 5/16" nut driver ($8) — Cabinet and bracket screws on most front-load machines are 5/16" hex.
• Phone camera ($0) — Photograph connector positions before unplugging anything.
• Multimeter ($25) — Confirm continuity before replacing an electrical part.

The repair, in order

1. Rule out the cheaper causes first - fans, sensor, damper, door switch.
2. Inspect the board for scorching or swollen capacitors.
3. Transfer connectors one at a time against your photographs.

How you know it worked. Normal cooling and display behaviour over 24 hours.

In your manual: the manual — checked; its troubleshooting section does not cover this part.

Worth fixing? Repair - the part is a small fraction of a new machine. Part $54.99–$129.00 against $1,399.99 for a new machine (9.2%).Part cost only. A service call adds a regional diagnostic fee plus labour.

Door seal

DIY.

Check, in this order

1. Do the paper test: close a sheet of paper in the door and pull - it should drag on all four sides.
2. Look for frost or condensation forming near the door edge, which the manual attributes to a door not closing properly.
3. Check the gasket for tears, and for food or a drawer holding the door open.

Before you open anything

• Unplug the refrigerator for any panel work.

Tools

• Hair dryer ($0) — Thawing an iced evaporator or reshaping a deformed door gasket.
• Flashlight ($0) — Boot, sump and pump housings are dark.

The repair, in order

1. Clean the gasket first - the manual lists a dirty gasket as a frost cause.
2. Do the paper test: close a sheet of paper in the door and pull; it should drag.
3. Warm a deformed gasket gently with a hair dryer and reshape before buying one.
4. If torn, peel the old gasket from its channel and press the new one in from the corners out.

How you know it worked. Paper test drags on all four sides and frost does not return at the door edge.

In your manual: The doors will not close completely — page 14

Worth fixing? Repair - the part is a small fraction of a new machine. Part $45.88–$115.68 against $1,399.99 for a new machine (8.3%).Part cost only. A service call adds a regional diagnostic fee plus labour.

We rank every refrigerator we hold certification data for, within its own size and configuration class, so you are comparing machines that would fit the same space. See the refrigerator rankings →