It's not heating — clothes come out cold and damp — temperature select switch
The drum isn't turning — I hear it hum but nothing spins — motor pulley
It's making a squealing, thumping, or scraping noise — front panel felt seal
It won't start — nothing happens when I press the button — power cord
The steam or wrinkle-release cycle isn't doing anything — steam valve assembly
Codes on the display
Code
What it means
Evidence
F4E4
will not run
a repair video for this brand and appliance, not confirmed on this model
Documented failures
Motor pulley
Usually DIYVendor replaces this part if the drum will not spin
DIY.
Try this first — it costs nothing. Nothing free — a worn or loose motor pulley is a mechanical fault, though check the belt condition at the same time since both wear together.
Check, in this order
Check whether the belt is slipping on the pulley shaft rather than the pulley itself being the fault — a glazed belt can look identical.
Look for a worn or glazed groove on the pulley where the belt rides.
Confirm the pulley is seated tight on the motor shaft and not just spinning loose.
Before you open anything
Unplug the dryer or cut power at the breaker.
If this is a gas dryer, also shut off the gas supply valve before opening the cabinet.
Tools
5/16" nut driver ($8) — Cabinet and bracket screws on most front-load machines are 5/16" hex.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Remove the belt to access the motor shaft and pulley.
Photograph the belt routing before fully removing it.
Swap the pulley, reseat it fully on the shaft, and re-thread the belt exactly as photographed.
How you know it worked. The drum turns at full speed with no belt slip and no unusual noise from the motor area.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $8.57–$25.93 against $864.51 for a new machine (3.0%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Front panel felt seal
Usually DIYVendor replaces this part if the dryer takes too long, due to poor heat retention
DIY.
Try this first — it costs nothing. Nothing free — a worn felt seal causing metal-on-fabric rubbing needs replacing, but confirm it's actually the seal and not a roller before ordering.
Check, in this order
Confirm the scraping noise is steady rather than rhythmic — a worn felt seal rubs constantly, while a bad roller or pulley pulses with drum speed.
Look at the seal for a flattened or torn section where the drum has worn through it.
Check that the drum is still seated square in its track, since a shifted drum can also cause rubbing.
Before you open anything
Unplug the dryer or cut power at the breaker.
Tools
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Thin putty knife ($5) — Releasing clips without marking the cabinet.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Remove the front panel to expose the felt seal around the drum opening.
Photograph its position and peel out the old seal.
Press the new seal into its channel evenly so it doesn't bunch on one side.
How you know it worked. The scraping sound is gone through a full cycle.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $8.90–$43.61 against $864.51 for a new machine (5.0%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Steam valve assembly
Usually DIYVendor replaces this part if the steam function in the dryer will not work properly
DIY.
Try this first — it costs nothing. Confirm the household water valve is open and the inlet screen is clean — the same free checks as the inlet valve rule out most no-steam complaints.
Check, in this order
Confirm the water inlet valve itself is passing water before condemning the steam valve downstream.
Look for water pooling under the machine, which points at a stuck-open valve rather than an electrical fault.
Check the wiring connector to the valve for a solid connection.
Before you open anything
Unplug the dryer or cut power at the breaker.
Close the household water valve behind the dryer before disconnecting any hose.
Tools
Slip-joint pliers ($12) — Hose clamps and inlet filter screens.
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Shallow pan and towels ($0) — Residual water always comes out, even after draining.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Close the water valve and bail any residual water.
Photograph the hose and wiring connections before disconnecting.
Swap the valve assembly, reconnect the hose, and check for drips before restoring power.
How you know it worked. Steam or wrinkle-release cycles run normally with no puddle under the machine afterward.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $97.00 against $864.51 for a new machine (11.2%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Power cord
Usually DIYVendor replaces this part if the dryer will not turn on at all
DIY. Get an electrician if the outlet itself tests dead — that's house wiring, not the appliance.
Try this first — it costs nothing. Try a different outlet or test the current one with a meter — a tripped breaker or dead outlet looks identical to a dead cord.
Check, in this order
Test the outlet with a different appliance or a plug-in tester before condemning the cord.
Look for scorch marks or a loose prong at the plug end, which confirms a failing cord even with a good outlet.
Check the terminal block connections inside the dryer for a burnt or loose lead.
Before you open anything
Unplug the dryer before touching the terminal block — it carries 240V.
Confirm the outlet itself is dead before assuming the cord is the fault.
Tools
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Multimeter ($25) — Confirm continuity before replacing an electrical part.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Unplug the dryer and pull it out to reach the terminal block on the back.
Photograph the wire positions — the neutral and ground configuration matters and varies by cord type.
Swap the cord and match every lead to its original terminal.
How you know it worked. The dryer powers on reliably and the plug stays cool to the touch after a full cycle.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $29.99–$57.80 against $864.51 for a new machine (6.7%).Part cost only. A service call adds a regional diagnostic fee plus labour.
Temperature select switch
Usually DIYVendor replaces this part if the dryer will not change to the selected temperature
DIY.
Try this first — it costs nothing. Wiggle the dial and try each heat setting again after a firm push — a loose knob shaft sometimes just isn't seating the switch fully.
Check, in this order
Confirm the symptom follows the switch position — heat working on some settings and not others points here rather than at the heating source itself.
Test the switch for continuity in each position.
Check the wiring harness behind the console for a loose spade connector, which mimics a bad switch.
Before you open anything
Unplug the dryer or cut power at the breaker.
If this is a gas dryer, also shut off the gas supply valve before opening the cabinet.
Tools
#2 Phillips screwdriver ($6) — Panel and bracket screws.
Multimeter ($25) — Confirm continuity before replacing an electrical part.
Phone camera ($0) — Photograph connector positions before unplugging anything.
The repair, in order
Remove the console panel to reach the switch.
Photograph the wiring, then swap the switch.
Reconnect every wire in its original position and test each heat setting before closing the console.
How you know it worked. Every heat setting produces the expected temperature through a full cycle.
Prices are a snapshot taken on the date shown and are not monitored. Check the retailer before buying.
Worth fixing? Repair - the part is a small fraction of a new machine. Part $5.44–$14.95 against $864.51 for a new machine (1.7%).Part cost only. A service call adds a regional diagnostic fee plus labour.
If you replace it instead
Configuration-matched to this machine (vented, gas, ~7.4 cu ft). Prices are UPC-verified Amazon listings, not estimates. Like-for-like replacement rarely pays for itself on energy alone — replace for fit and features, or because the repair maths above says so.
A candidate must match this machine's configuration (style, fuel and defrost class) before price or efficiency is considered. Prices are a snapshot from the date shown; availability is not monitored — check the retailer before buying.