GE Dishwasher Won't Drain: 3 Causes, Ranked
Drain Pump
- 94.6%of repair attention
- $187.26part on Amazon ›
- 60 minto check
- Multimeter neededDIY
A physical obstruction you clear by hand costs nothing; no continuity on the motor means the pump itself has failed.
Check yours now ↓One cause below (circulation pump) is not a DIY job. Two checks cost nothing — do those first.
⚠ Cut power at the breaker and shut the water supply valve before opening the base or the junction box. There is standing water in the sump under the filter, so work with a towel and a shallow pan.
Two checks that cost nothing
- Check the filter and drain basket Pull the lower rack and look at the filter assembly and the small basket or trap next to it at the bottom of the tub. A bottle cap, piece of glass, chicken bone, or produce sticker can lodge there and block the pump from moving water out. Clear anything you find and run the drain cycle again.
- Check the drain hose for a kink Look under the sink where the drain hose connects, usually to the garbage disposal or a dedicated drain fitting. A hose that's been pinched, kinked, or pushed down without a high loop can trap water and stop the dishwasher from emptying. Straighten it out and secure it high under the counter if it's sagging.
- Check for a disposal knockout plug If the garbage disposal was installed or replaced recently, check whether the plastic knockout plug inside its dishwasher inlet was removed. Left in place, it seals that opening completely and nothing can drain, no matter what's wrong or right with the dishwasher itself. This is a common miss after any disposal swap.
Check each cause, easiest first
Ordered by how hard each is to check, not by how likely it is — so the cheap answers get ruled out before you open anything. The badge on each row shows where the smart money is. Percentages are share of repair-video attention, not a measured failure rate.
drain pump#1 most-watched · 94.6% of repair videos $187.26
How to check. Access is usually through the base panel or by pulling the machine out — cut power at the breaker first. Check the pump housing and impeller for a lodged object, and test continuity across the pump motor with a multimeter.
A physical obstruction you clear by hand costs nothing; no continuity on the motor means the pump itself has failed.
We earn a commission on Amazon purchases made through these links. It never changes which cause we rank first or what a part costs you.
Price checked 27 Aug 2026. Amazon prices move — the link always shows the current one.
water inlet valve#2 most-watched · 3.6% of repair videos $16.37
How to check. Shut off the water supply and cut power at the breaker, then pull the valve and look for mineral scale blocking the inlet screen; if it looks clear, test the solenoid coil for continuity with a multimeter.
No continuity, or a screen packed with scale, means the valve isn't opening reliably — that shows up as poor fill (weak cleaning or no heat buildup) or, on a valve stuck partly open, as a slow leak.
Price checked 27 Aug 2026. Amazon prices move — the link always shows the current one.
circulation pump#3 most-watched · 1.8% of repair videosPro job —
How to check. This one usually means pulling the machine out from under the counter and opening the base — cut power at the breaker and shut the water supply first. With the pump exposed, check the impeller for jammed debris, and listen or feel for the motor running when a cycle starts.
⚡ This one check needs the appliance plugged IN and running — the rest do not. Keep hands clear of the panel, touch nothing inside while it is live, and unplug again before replacing anything.
A jammed impeller you can clear by hand is a free fix; a motor that stays silent even with power reaching it has failed and needs replacing — confirm power is reaching it before condemning the pump.
No confirmed GE part for this yet. The diagnosis and the walkthrough still apply — but we would rather show you nothing than a part from a different manufacturer. Check your model's parts list before ordering anything for this cause.
Can the manufacturer refuse to sell you this part? It depends on your state.
If a circulation pump turns out to be your fault, you may need an official part. Whether a manufacturer has to sell you one is state law, not company policy — and it is not uniform.
| California | covered | SB-244 names major appliances explicitly. Parts, tools and documentation must be offered on fair terms — 7 years for parts wholesaling at $100+. |
|---|---|---|
| Colorado | covered | HB24-1121's 14-item exclusion list omits appliances, so they are covered. Includes a parts-pairing ban. |
| Oregon | covered | Appliances are not excluded from Oregon's right-to-repair statute. |
| Minnesota | likely covered | Appliances are not named as excluded and the definition is broad, but the statute does not name them either — read as covered, not confirmed. |
| New York | excluded | Home appliances are carved out BY NAME from the Digital Fair Repair Act. A manufacturer is not required to sell you this part. |
| Texas | excluded | Appliances are explicitly excluded from the state's repair statute. |
Enforcement is by the state Attorney General in every state confirmed — none of these laws gives you a personal right to sue. Sourced from primary statute text; see our right-to-repair notes for citations.
Is it worth fixing at all?
Most pages answer this with the “50% rule” — spend no more than half a replacement's price. We went looking for the origin of that number and could not find one: it is widely credited to ENERGY STAR, whose actual published guidance is an age-and-condition checklist with no percentage in it. We use your machine's own measured running cost instead. We hold it for 91 GE dishwasher models.
We rank every dishwasher we hold certification data for within its own size and configuration class — so you are comparing machines that would actually fit the same space. See the dishwasher rankings →
When to stop and call someone
Leave the appliance alone, ventilate, and call the gas utility. Nothing on this page is worth doing around a suspected leak.
Compressor and refrigerant repairs need EPA certification — that is a legal requirement, not a difficulty rating. A service call runs roughly $75–$150 before parts, so read the repair-or-replace maths above before booking.
Common questions
Share of repair-video views for this symptom across 246 videos. The walkthroughs shown on this page come from RepairClinic.com — a single supplier's channel, which is a limit worth knowing. It measures what people watch. That correlates with what fails, but video age, channel size and search visibility all influence it, so we publish it as attention and never as a failure rate. Each cause shows the video count and total views behind its percentage.
We only show a part when it comes from a repair on a machine in the same GE family. Where we have no family-matched part we say so rather than substitute another brand's. For parts confirmed on one exact machine, use the model page above.
Usually yes for simple mechanical parts like belts, fuses and thermostats; less reliably for control boards and sensors, where tolerances and firmware matter. Every listing is labelled.
Know your model number?
These GE dishwashers have a fully verified repair page — every failure sourced, every part confirmed on that exact machine, rather than matched at family level as above.